2012 AviationLearning.net. All Rights Reserved.
"Your Online Training Resource"
A student number is issued on first module payment please quote it for all other payments and tutor requests.
Modules not currently on line will be supplied on request.
Part 66 PURCHASE OPTIONS
PRIVATE PURCHASE £30.00 GBP
SOTECH STAFF £20.00 GBP
FEAM STAFF £20.00 GBP
ENGMA VIETNAM £20.00 GBP
5 MODULES £90.00 GBP
11 MODULES £180.00 GBP
17 MODULES £300.00 GBP
PAY THE FEE TO RECIEVE THE PASSWORD
THEN CLICK ON THE MODULE TO DOWN LOAD.
EASA PART-66 MODULE 7 : MAINTENANCE PRACTICE
7.1 Safety Precautions-Aircraft and Workshop (level 3)
Aspects of working practices including precautions to take when working with electricity, gases especially oxygen, oils and chemicals.
Also, instruction in the remedial action to be taken in the event of a fire or another accident with one or more of these hazards including knowledge on extinguishing agents.
7.2 Workshop Practices (level 3)
Care of tools, control of tools, use of workshop materials;
Dimensions, allowances and tolerances, standards of workmanship;
Calibration of tools and equipment, calibration standards.
7.3 Tools (level 3)
Common hand tool types;
Common power tool types;
Operation and use of precision measuring tools;
Lubrication equipment and methods.
Operation, function and use of electrical general test equipment;
7.4 Avionic General Test Equipment (level 2)
Operation, function and use of avionic general test equipment.
7.5 Engineering Drawings, Diagrams and Standards (level 2)
Drawing types and diagrams, their symbols, dimensions, tolerances and projections;
Identifying title block information;
Microfilm, microfiche and computerised presentations;
Specification 100 of the Air Transport Association (ATA) of America;
Aeronautical and other applicable standards including ISO, AN, MS, NAS and MIL;
Wiring diagrams and schematic diagrams.
7.6 Fits and Clearances (level 2)
Drill sizes for bolt holes, classes of fits;
Common system of fits and clearances;
Schedule of fits and clearances for aircraft and engines;
Limits for bow, twist and wear;
Standard methods for checking shafts, bearings and other parts.
7.7 Electrical Wiring Interconnection System (EWIS) (level 3)
Continuity, insulation and bonding techniques and testing;
Use of crimp tools: hand and hydraulic operated;
Testing of crimp joints;
Connector pin removal and insertion;
Co-axial cables: testing and installation precautions;
Identification of wire types, their inspection criteria & damage tolerance
Wiring protection techniques: Cable looming and loom support, cable clamps, protective sleeving techniques including heat shrink wrapping, shielding.
EWIS installations, inspection, repair, maintenance & cleanliness standard.
7.8 Riveting (level 2)
Riveted joints, rivet spacing and pitch;
Tools used for riveting and dimpling;
Inspection of riveted joints.
7.9 Pipes and Hoses (level 2)
Bending and belling/flaring aircraft pipes;
Inspection and testing of aircraft pipes and hoses;
Installation and clamping of pipes.
7.10 Springs (level 2)
Inspection and testing of springs.
7.11 Bearings (level 2)
Testing, cleaning and inspection of bearings;
Lubrication requirements of bearings;
Defects in bearings and their causes.
7.12 Transmissions (level 2)
Inspection of gears, backlash;
Inspection of belts and pulleys, chains and sprockets;
Inspection of screw jacks, lever devices, push-pull rod systems
7.13 Control Cables (level 2)
Swaging of end fittings;
Inspection and testing of control cables;
Bowden cables; aircraft flexible control systems.
7.14 Material handling (level 2)
7.14.1 Sheet Metal
Marking out and calculation of bend allowance;
Sheet metal working, including bending and forming;
Inspection of sheet metal work.
7.14.2 Composite and non-metallic
7.15 Welding, Brazing, Soldering and Bonding (level 2)
(a) Soldering methods; inspection of soldered joints.
(b) Welding and brazing methods;
Inspection of welded and brazed joints;
Bonding methods and inspection of bonded joints.
7.16 Aircraft Weight and Balance (level 2)
(a) Centre of Gravity/Balance limits calculation: use of relevant documents;
(b) Preparation of aircraft for weighing;
7.17 Aircraft Handling and Storage (level 2)
Aircraft taxiing/towing and associated safety precautions;
Aircraft jacking, chocking, securing and associated safety precautions;
Aircraft storage methods;
Electrical, hydraulic and pneumatic ground supplies.
Effects of environmental conditions on aircraft handling and operation.
7.18 Disassembly, Inspection, Repair and Assembly Techniques (level 2)
(a) Types of defects and visual inspection techniques.
Corrosion removal, assessment and reprotection.
(b) General repair methods, Structural Repair Manual;
Ageing, fatigue and corrosion control programmes;
(c) Non destructive inspection techniques including, penetrant, radiographic, eddy current,
ultrasonic and boroscope methods.
(d) Disassembly and re-assembly techniques.
(e) Trouble shooting techniques
7.19 Abnormal Events (level 2)
(a) Inspections following lightning strikes and HIRF penetration.
(b) Inspections following abnormal events such as heavy landings and flight through
7.20 Maintenance Procedures (level 2)
Interface with aircraft operation;
Maintenance Inspection/Quality Control/Quality Assurance;
Additional maintenance procedures;
Control of life limited components
MODULE 7 B1
MODULE 7 B2
AT OUR DUBLIN TRAINING CENTRE
B787 B1/B2 ALL SERIES ALL ENGINES THEORY AND PRACTICAL LOCATION DUBLIN
CONTACT FOR DETAILS
A350 B1/B2 THEORY AND PRACTICAL LOCATION DUBLIN
CONTACT FOR DETAILS
Contact: David Taylor email@example.com
Contact us on:
AviationLearnining.firstname.lastname@example.org Phone:+44 (0)1506463056
CAUTION: BY PURCHASING AND/OR DOWNLOADING ANY MATERIAL FROM THIS SITE YOUR CONFIRM YOU WILL RESPECT ANY COPYRIGHTS OF AVIATIONLEARNING OR ANY OTHER LEGAL COPYRIGHT HOLDER PUBLISHED ON THIS SITE.
FURTHER YOU ARE NOT ACTING AS THE AGENT OF ANOTHER COMPANY NOR WILL YOU SHOW, LEND, COPY OR PRINT ANY DOCUMENT WITHOUT SPECIFIC PERMISSION OF AviationLearning.net.